单项选择题
The following command output was gathered from Router R1, an ABR between areas 0 (backbone) and area 1. In this internetwork, area 0 contains all the subnets of cla ss A network 10.0.0.0. R1's OSPF process has a distribute - list prefix question in command configured. Assuming the subnets listed in the answers actually exist in area 0.
Which of the following occurs on router R1?（）
R1#sh ip prefix - list
ip prefix - list question: 4 entries
seq 5 deny 10.1.2.0/24 ge 25 le 27
seq 15 deny 10.2.0.0/16 ge 30 le 30
seq 20 permit 0.0.0.0/0 le 32
A. R1 will not create/flood a type 3 LSA for subnet 10.1.2.0/26 into area 1
B. R1 will not create/flood a Type 3 LSA for subnet 1 0.1.2.0/24 into area 1
C. R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablE
D. R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
相关考题
-
单项选择题
Router B1, an internal router in area 1, displays the following output. The only two ABRs connected to area 1 are performing Type 3 LSA filterinG. Which of the following answers is true based on the information in the output from B1?（） R1# show ip route 10.1.0.0 255.255.0.0 longer - prefixes ! Legend lines omitted for brevity 10.0.0.0/8 is variably subnetted, 17 subnets, 3 masks O 10.1.2.0/24 [110/658] via 10.10.13.1, 00:00:32, Serial0/0/0.1 O IA 10.1.1.0/24 [110/658] via 10.10.23.2, 00:41:39, Ser ial0/0/0.2 O IA 10.1.3.0/24 [110/658] via 10.10.23.2, 00:41:39, Serial0/0/0.2
A. A Type 3 LSA for 10.2.2.0/24 was filtered by both ABRs
B. A Type 3 LSA for 10.1.2.0/24 was not filtered by both ABRs
C. A Type 3 LSA for 10.1.3.0/24 was not filtered by at least one ABR
D. A Type 3 LSA for 10.1.1.0/24 filtered by both ABRs -
多项选择题
Which of the following LSA types describe information related to topology or subnets useful for calculating routes for subnets inside the OSPF domain?（）
A. 1
B. 2
C. 3
D. 4
E. 5
F. 7 -
多项选择题
The following output was taken from Router R3. A scan of R3s configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1
A. An a uto - cost reference - bandwidth 1000 command in router ospf mode
B. An auto - cost reference - bandwidth 2000 command in router ospf mode
C. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf mode
D. An auto - cost reference - bandwidth 64700 command i n router ospf mode
